Afficher panier (0 Article) Mon compteAfficher bloc-notesAller à la caisse


Solaris® is a low viscosity, clear and colorless liquid platinum cure silicone rubber compound designed for use in protecting of electronic components and other assemblies. It will protect components against shock, vibration, moisture, ozone, dust, chemicals and other environmental hazards.

  • Solaris® silicone d'encapsulaion

    Solaris ® a une faible viscosité, limpide et incolore, c´est un silicone polyaddition liquide conçu pour une utilisation dans la protection des composants électroniques et autres assemblages. Il permettra de protéger les composants...

    85,95 EUR (Prix exclusif 21% TVA)

  • Solaris Primer Pint

    POUR UNE ADHÉSION MAXIMUM AU VERRE - UTILISEZ SOLARIS® PRIMER BONDING ... Toutes les surfaces en verre doivent être propres avant d'appliquer Solaris® Bonding Primer®

    14,40 EUR (Prix exclusif 21% TVA)

  • Solaris® Clear Silicone Encapsulant /7,26 kg

    Solaris ® a une faible viscosité, limpide et incolore, c´est un silicone polyaddition liquide conçu pour une utilisation dans la protection des composants électroniques et autres assemblages. Il permettra de protéger les composants contre les chocs, les vibrations, l'humidité, l'ozone, la poussière, les produits chimiques et autres risques environnementaux par enrobage ou encapsulation des composants et assemblages.

    406,40 EUR (Prix exclusif 21% TVA)

Safety – Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Wear vinyl gloves only. Latex gloves will inhibit the cure of the rubber.

Store and use material at room temperature (73°F/23°C). Storing material at warmer temperatures will reduce the usable shelf life of unused material. These products have a limited shelf life and should be used as soon as possible.


All glass surfaces must be clean before applying Solaris® Bonding Primer®

Glass surface preparation:

Step 1- Wipe glass surfaces using Isopropyl Alcohol applied with lintfree paper towels. Let dry for 10 minutes.

Step 2 - Wipe the glass surfaces with ammonia-based glass cleaner applied with lint-free paper towels. Let dry for 10 minutes.

Note: Do not touch glass surface after cleaning.

When glass surface is clean, apply one coat of Solaris® Bonding Primer® using a clean, dry paint brush and let dry for 10 minutes.

A hazy film will form on the glass surface. Wipe away film using a lintfree cloth until surface is clear.

Apply a second coat of Solaris® Bonding Primer®, let dry for 10 minutes and wipe surface until clear.

You are now ready to apply the Solaris® Silicone Encapsulant to the prepared glass surface.


Solaris® silicone rubber compound will cure in contact with most clean, dry surfaces. However, certain materials, such as butyl and chlorinated rubber, materials containing sulfur, amines, and non-platinum RTV silicone rubber compounds will cause cure inhibition and rubber will not cure.

If compatibility between the rubber and the surface is in question, a smallscale test is recommended. Inhibition has occurred if the rubber is gummy or uncured after the recommended cure time has passed.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.


Before you begin, pre-mix Part B thoroughly. After dispensing required amounts of Parts A and B into mixing container (1A:1B by volume or weight), mix thoroughly for 3 minutes making sure that you scrape the sides and bottom of the mixing container several times. After mixing thoroughly for 3 minutes, empty the contents of your mixing container into a second clean mixing container and mix again for another 2 to 3 minutes before pouring. This technique is your best bet for successful mixing.

For best results, vacuum degassing is recommended to help eliminate any entrapped air. Subject mixture to 29” of mercury in a vacuum chamber until mixture rises, breaks and falls. Allow for 3 to 4 times volume expansion in mixing container. Be aware of pot life so that material does not set up in mixing container.

Pouring - For best results, pour your mixture in a single spot at the lowest point of the containment field. Let the rubber seek its own level. A uniform flow will help minimize entrapped air.

Curing - Allow rubber to cure for 24 hours at room temperature (73°F/23°C) before demolding. Do not cure rubber where temperature is less than 65°F/18°C.

Naviguer par application ..

Ces produits sont classés par application telles que, le moulage du corps humain, le moulage, les tirages, les produits transparents, la restoration, le prototypage, etc...

  • Moulage

    Une gamme de matériaux de moulage souples et rigides.

  • Tirage

    Une large gamme de matériaux de tirage souples et rigides

  • special properties

  • Matériaux composites

    Résines et fibres pour la construction en matériaux composites.

  • Mousses

    Mousse PU flexible liquide, mousse PU rigide liquide, blocs de mousse PU rigide et mousse de latex.

  • Restauration

    Matériaux pour la restauration des ornements et des bâtiments, à l'intérieur et à l'extérieur.

  • Prototypage

    Matériaux utilisés pour le prototypage rapide.

  • Textile

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

Informations générales Options d'envoi Costumer Projects Marques Applications Branches