Afficher panier (0 Article) Mon compteAfficher bloc-notesAller à la caisse

AquaCon®

AquaCon® is a water based concrete release agent that aids in releasing concrete castings from Smooth-On rubber molds and other surfaces such as melamine, metal and non-porous (sealed) wood. It provides a clean, positive release, does not interfere with color or surface detail and helps minimize bug holes and air bubbles in finished castings. Coverage – Applied in a thin film (.0005 in / .013 mm), 1 gallon (undiluted) covers 3,200 square feet / 297 square meters.

  • AquaCon démoulant béton /3,76kg

    est un agent de démoulage pour béton à base d'eau qui aide à démouler des pièces moulées en béton à partir de moules en élastomère Smooth-On. Bouteille 3,76 kg.

    41,50 EUR (Prix exclusif 21% TVA)

Features
Low Cost – Use straight or dilute with water (up to 8 parts with water. See dilution recommendation below).
Water Based, Eco-Friendly – Contains no VOC’s, carcinogens or oils harmful to the environment.
Does Not Stain Concrete, affect color surface detail or finishing.
Minimizes “Bug Holes” and air bubbles.
Contains No Oils that will cause rubber molds to soften, shrink or swell.
Keeps Molds Clean - Does not build up.
Extends Mold Life
Instructions
PREPARATION... Safety - Wear safety glasses to minimize contamination risk. Store and use at room temperature (73°F/23°C). Do not use below 45°F/8°C.

Pre-Mixing - Before dispensing, shake container or stir thoroughly with a paddle or drill mixer set on a slow speed to a uniform consistency.

Diluting AquaCon® - AquaCon® can be used straight or diluted with up to 8 parts water. The dilution ratio depends on your concrete mix design. Finding the right balance between AquaCon® and water can affect bug holes. If using on a new rubber mold, it is recommended that AquaCon® be used straight (undiluted) for each casting for the first 10 castings. 1 – 10 castings, use undiluted. After 10 castings, dilute 1 part AquaCon® : 4 Parts Water After 20 castings, dilute 1 part AquaCon® : 8 Parts Water Mix only amount needed for one day. Mixture may separate in the container after a few hours. Before dispensing, pre-mix before to a uniform consistency.

Applying - Coat mold surface with a very thin film (.0005 in / .013 mm). Apply with a brush, roller, HVLP gun or Kwikee® Sprayer. Do not allow release agent to pool in the mold. Wipe over mold surface using a clean, soft cloth.

Caution: Do Not Over Apply. Applying too much release agent will cause air bubbles “wormtracks”, “bugholes” or pitting on surfaces. After applying AquaCon to mold surface, you can mix and cast concrete immediately.

Mix only amount needed for one day. Mixture may separate after 24 hours. Re-mix to a uniform consistency and apply. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Naviguer par application

Ces produits sont classés par application telles que, le moulage du corps humain, le moulage, les tirages, les produits transparents, la restoration, le prototypage, etc...

  • Moulage

    Une gamme de matériaux de moulage souples et rigides.

  • Tirage

    Une large gamme de matériaux de tirage souples et rigides

  • special properties

  • Matériaux composites

    Résines et fibres pour la construction en matériaux composites.

  • Mousses

    Mousse PU flexible liquide, mousse PU rigide liquide, blocs de mousse PU rigide et mousse de latex.

  • Restauration

    Matériaux pour la restauration des ornements et des bâtiments, à l'intérieur et à l'extérieur.

  • Prototypage

    Matériaux utilisés pour le prototypage rapide.

  • Textile

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

Informations générales Options d'envoi Costumer Projects Marques Applications Branches