Afficher panier (0 Article) Mon compteAfficher bloc-notesAller à la caisse

Universal Mold Release

Universal® Mold Release Agent is formulated especially for mold making and casting, and works well with most liquid rubber and liquid plastic products. It will release mold rubbers (such as polyurethanes and polysulfides) from properly prepared models. Sealing porous models (wood, plaster, concrete) or certain modeling clays (containing water or sulfur) with Smooth-On SuperSeal® or other sealer may be necessary. Universal® Mold Release is effective over a broad temperature range from 70°F to 500°F.

  • Universal Mold Release aerosol /400gr

    L'Universal Mold Release est un additif spécialement conçu pour faciliter le démoulage des élastomères polyuréthanes et polysulfures - Spray 400 gr.

    15,35 EUR (Prix exclusif 21% TVA)

  • Universal Mold Release liquide /100ml

    L'Universal Mold Release est un additif spécialement conçu pour faciliter le démoulage des élastomères polyuréthanes et polysulfures - Liquide en flacon 100 ml.

    6,70 EUR (Prix exclusif 21% TVA)

  • Universal Mold Release /2,77 kg

    L'Universal Mold Release est un additif spécialement conçu pour faciliter le démoulage des élastomères polyuréthanes et polysulfures. Bidon 2,77 kg.

    71,60 EUR (Prix exclusif 21% TVA)

Transport Regulated Goods

The transport of items out of this group can be restricted due to EU restrictions and regulations and will require a specialized carrier. Transport costs will not be automatically calculated. We will give you transport options and a quote later. Preparing this order for transport will not fit within our normal time frame and delivery may take a few days longer.

Features
If using silicone rubber, seal model surface with SuperSeal® only. Do not use Universal® Mold Release. Universal® Mold Release also easily releases a variety of casting materials (epoxies, Smooth-On liquid plastics, etc.) from cured rubber molds. This product has a limited shelf life and should be used as soon as possible. Properly used, Universal® Mold Release improves molding efficiency for a variety of casting applications and will actually lengthen the life of your production mold.

Universal® Mold Release is available in aerosol spray or economical liquid form (one gallon, 5 gallon and 55 gallon drum.)

Instructions
Aerosol USE ONLY WITH ADEQUATE VENTILATION:

Shake well before using.
Hold can 12 in./30cm. from surface to be sprayed.
Apply a continuous light mist coating to model or mold surface and surrounding forms.
Using a soft brush, brush the release agent over entire surface of model or mold in order to break the surface tension and minimize air entrapment.
Apply another light mist coating of release agent and let stand for 5 minutes.
You are now ready to apply mold rubber or cast into a cured rubber mold.
Liquid Application:

This product has a limited shelf life and should be used as soon as possible.
Can be put into non-aerosol plant sprayer, deck sprayer, or applied with soft brush.
Apply thorough thin coating over entire surface of model or mold.
Allow surface solvents to evaporate for 5 minutes.
Compressed air or hair dryer may be used to blow off any excess that has pooled.
Repeat application and allow to dry.
You are now ready to apply mold rubber or cast into a cured rubber mold.
Because no two applications are quite the same, a small test application to determine suitability is recommended if performance of this material is in question.

Painting A Finished Casting…

One method for applying paint to a casting is to remove release agent from casting with a solvent such as isopropyl alcohol or acetone. Next, apply one to two coats of auto body primer (available at most auto parts stores) and let dry. Finally, apply acrylic or similar base paint.

Naviguer par application

Ces produits sont classés par application telles que, le moulage du corps humain, le moulage, les tirages, les produits transparents, la restoration, le prototypage, etc...

  • Moulage

    Une gamme de matériaux de moulage souples et rigides.

  • Tirage

    Une large gamme de matériaux de tirage souples et rigides

  • special properties

  • Matériaux composites

    Résines et fibres pour la construction en matériaux composites.

  • Mousses

    Mousse PU flexible liquide, mousse PU rigide liquide, blocs de mousse PU rigide et mousse de latex.

  • Restauration

    Matériaux pour la restauration des ornements et des bâtiments, à l'intérieur et à l'extérieur.

  • Prototypage

    Matériaux utilisés pour le prototypage rapide.

  • Textile

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

Informations générales Options d'envoi Costumer Projects Marques Applications Branches