Afficher panier (0 Article) Mon compteAfficher bloc-notesAller à la caisse

Kick-It accélérateur pour élastomère PU

Kick-It Accelerateur

C'est un additif conçu pour "accélérer" le temps de durcissement de certains produits élastomère uréthane liquide Smooth-On.

Fiche technique Kick-iT

Produits Kick-It

  • Kick-It accellerateur /500ml

    Additif conçu pour "accélérer" le temps de durcissement de certains produits élastomère uréthane liquide Smooth-On. - Flacon 500 ml.

    45,25 EUR (Prix exclusif 21% TVA)

  • Kick-It accellerateur /100ml

    Additif conçu pour "accélérer" le temps de durcissement de certains produits élastomère uréthane liquide Smooth-On. - Flacon 100 ml.

    10,12 EUR (Prix exclusif 21% TVA)

Instructions
Safety – Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Store and use all products at room temperature. This product has a limited shelf life and should be used as soon as possible. Wear gloves and eye protection to minimize risk of contamination.

Measuring and Mixing - All components must be measured using an accurate gram scale. The accelerator is added by weight to Part B and should be thoroughly mixed into Part B before adding Part A.

Note: Adding the accelerator significantly reduces the pot life (time you have to mix and pour material) of the liquid rubber product. This product has a limited shelf life and should be used as soon as possible.

Note - No significant increase in demold time was noticed at percentages greater than 3% except with PMC® urethane rubbers, which can be accelerated at greater speeds than ReoFlex® or VytaFlex®. Demold time can generally reduced by one half by exposing the material to 150° F.

Example – VytaFlex®10 (1:1 Mix Ratio): To reduce the demold time of VytaFlex® 10 from 24 hours to 7 hours, add 30 grams of accelerator to 1000 grams of VytaFlex® 10 Part B. Mix thoroughly for at least one minute, making sure that you scrape the sides and bottom of your container several times. Next, add 1000 grams of Part A and mix thoroughly for at least one minute, again making sure that you scrape the bottom and sides of your container several times. Pour the contents into a clean separate container and mix thoroughly. This will help to ensure that unmixed material does not contaminate the mold. Do not delay between mixing and pouring, as your pot life is about 6 minutes.

In about 7 hours, the rubber mold can be removed from the original model. Demold time can generally be reduced by ½ by exposing the material to 150° F.

Naviguer par application ..

Ces produits sont classés par application telles que, le moulage du corps humain, le moulage, les tirages, les produits transparents, la restoration, le prototypage, etc...

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

  • Matériaux composites

    Résines et fibres pour la construction en matériaux composites.

  • Moulage

    Une gamme de matériaux de moulage souples et rigides.

  • Mousses

    Mousse PU flexible liquide, mousse PU rigide liquide, blocs de mousse PU rigide et mousse de latex.

  • Prototypage

    Matériaux utilisés pour le prototypage rapide.

  • Restauration

    Matériaux pour la restauration des ornements et des bâtiments, à l'intérieur et à l'extérieur.

  • special properties

  • Textile

  • Tirage

    Une large gamme de matériaux de tirage souples et rigides

Informations générales Options d'envoi Costumer Projects Marques Applications Branches