Afficher panier (0 Article) Mon compteAfficher bloc-notesAller à la caisse

Pigments fluorescents Ignite

Pigments fluorescents Ignite

La ligne de colorants fluorescents liquides Ignite® est compatible avec les élastomères uréthanes, les résines uréthanes, les mousses uréthanes (rigides et souples) et les silicones. Le fluorescent ou effet "luminescent" est maximisé sous la lumière ultra-violette ou «lumière noire». L'effet de couleur le plus spectaculaire est réalisé quand un colorant Ignite est utilisé avec un élastomère transparent ou translucide uréthane (comme Clear Flex 50) ou une résine (comme Smooth-Cast 325).

L'échantillonneur Ignite® comportant les 9 couleurs disponibles, vous donne la possibilité de découvrir chaque couleur sans dépenser beaucoup d'argent.

Lorsque vous ajoutez les pigments Ignite® fluorescents à un matériau uréthane, le tirage semble plus lumineux dans la lumière ambiante et semble s'allumer sous la lumière ultraviolette.

Fiche technique colorants fluorescents Ignite

Pigments Ignite

  • Ignite blanc fluo /120ml

    Ignite blanc fluo. Flacon 120 ml.

    18,30 EUR (Prix exclusif 21% TVA)

  • Ignite bleu fluo /120ml

    Ignite bleu fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite jaune fluo /120ml

    Ignite jaune fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite magenta fluo /120ml

    Ignite magenta fluo. Flacon 120ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite orange fluo /120 ml

    Ignite orange fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite rouge fluo /120ml

    Ignite rouge fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite rose fluo /120ml

    Ignite rose fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite orange fluo /120 ml

    Ignite orange fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite rouge fluo /120ml

    Ignite rouge fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

  • Ignite rose fluo /120ml

    Ignite rose fluo. Flacon 120 ml.

    22,50 EUR (Prix exclusif 21% TVA)

Instructions
To get you started, we offer the following colorant loading levels. Results may vary.

By Weight Using A Gram Scale: Add Ignite™ colorant at a ratio of between 0.5% - 1.5% of the total weight (Parts A + B mixed) of the material being cast. 1% pigment yields the best results. Adding more than 1.5% by weight offers no benefit and is a waste of the colorant. Too much colorant may cause cure inhibition.

By Volume Measured In Drops: Add 30 drops of Ignite™ per 3 oz (88 ml) of mixed urethane material. If using a translucent material (like Smooth-Cast 325) you can use 15 drops to maintain translucency of the material.

Pre-Mix Before Using: Ignite™ colorants are pigment dispersions and may separate over time. They must be thoroughly pre-mixed in the container before using with a liquid urethane product.

Directions For Use: After dispensing the required amount of urethane material Parts A and B into measuring containers, add colorant to Part B and mix thoroughly. Combine Parts A and B into a mixing container and mix as directed by the urethane product technical bulletin. Blending Colors - You can combine different colors on a pallete to create a custom color before adding to liquid urethane product as directed above. Recommended loading maximum is 1% Ignite pigment by weight.

Smooth-On offers this color guide as a general reference only and assumes no responsibility for color accuracy or matching. Results will vary from one material to another. The end user is solely responsible for determining color suitability and accuracy. Small scale testing is recommended. User determines amount to add; If this is your first time adding color tint or pigment to a urethane, epoxy or silicone system, you may want to test the color effect by adding a few drops to a small amount of urethane material and observe the outcome. It may take a few test castings to attain the desired color outcome.

Looking for a clear fluorescent additive? Cryptolyte™ is a clear additive that can be added to urethane or silicone materials that will cause cured material to glow a bright blue when exposed to UV light (black light).

For fluorescent color effects in platinum silicone rubbers, use Silc-Pig™ ELECTRIC silicone pigments

Naviguer par application ..

Ces produits sont classés par application telles que, le moulage du corps humain, le moulage, les tirages, les produits transparents, la restoration, le prototypage, etc...

  • Cosplay

    Products to make your own Cosplay Costumes and Props!

  • Matériaux composites

    Résines et fibres pour la construction en matériaux composites.

  • Moulage

    Une gamme de matériaux de moulage souples et rigides.

  • Mousses

    Mousse PU flexible liquide, mousse PU rigide liquide, blocs de mousse PU rigide et mousse de latex.

  • Prototypage

    Matériaux utilisés pour le prototypage rapide.

  • Restauration

    Matériaux pour la restauration des ornements et des bâtiments, à l'intérieur et à l'extérieur.

  • special properties

  • Textile

  • Tirage

    Une large gamme de matériaux de tirage souples et rigides

Informations générales Options d'envoi Costumer Projects Marques Applications Branches